Revision as of 14:50, 6 February 2017

Feedback to this page: click here

The Sputter coater 03 (Cressington)

The Sputter coater is used to sputter a thin gold layer on different small samples (smaller than 100 mm wafers). It is not allowed to use the sputter coater for other purposes.

One of the most effective ways to counter problems with charging on non-conducting samples during SEM investigations is to apply a conducting coating to the surface. The sputter coater allows you to coat small samples with a thin gold layer. When securely grounded, i.e. connected electrically with a sample holder using aluminium tape or clamps, the gold layer will effectively eliminate all charging problems in the SEM.

The sputter coater consists of a sputter chamber with a gold target and a stage. The stage consist of four smaller stages. These small stages can rotate individually in a planetary motion, when the entire stage rotates at the same time. The rotation speed can be controlled. Small samples can be mounted on a SEM pinstub holder (only use the smallest pinstubs) with carbon pads and then placed on one of the small stages. The maximum sample size is a 4 inch wafer. If your sample is larger than one of the four small stages, or if the sample is not fastened on a pinstub, the stage rotation should not be activated.

The machine is controlled by a control panel. The sputter process will be done automatically, but the sputter time can be adjusted.

Please note that the sputter rate and uniformity have not been measured yet.

Argon is used as a sputter gas to generate a plasma in the sputter chamber and to vent the chamber.

The Sputter coater 03 (Cressington) is located in the 346 basement, room 907 (next to the SEM Supra 1) .

The user manual and contact information can be found in LabManager:

Sputter coater 03

Process knowledge

Deposition of gold

Overview of the performance of the Sputter coater 03 (Cressington) and some process related parameters

Purpose		Gold sputter coating of different samples before SEM characterization
Performance	Film thickness	Not measured.
Performance	Deposition rate	Not measured
Process parameter range	Pressure	0.01 mbar (default value)
	Current	40 mA (default value)
	Sputter time	Maximum 30 s
Substrates	Batch size	One sample smaller than a 100 mm wafer Several smaller samples
Substrates	Allowed materials	All samples that are allowed in the SEM Supra 1

The Sputter coater 04 (Agar Scientific)

The Sputter coater is used to sputter a thin gold layer on different samples up to 100 mm wafers. It is not allowed to use the sputter coater for other purposes.

One of the most effective ways to counter problems with charging on non-conducting samples during SEM investigations is to apply a conducting coating to the surface. The sputter coater allows you to coat small samples with a thin gold layer. When securely grounded, i.e. connected electrically with a sample holder using aluminium tape or clamps, the gold layer will effectively eliminate all charging problems in the SEM.

The sputter coater consists of a sputter chamber with a gold target and a stage. Small samples can be mounted on a SEM pinstub holder (only use the smallest pinstubs) with carbon pads and then placed on one of the small holes. The maximum sample size is a 100 mm wafer.

The machine is controlled by a control panel. The sputter process will be done automatically, but the sputter time can be adjusted.

Please note that the sputter rate and uniformity have not been measured yet.

Argon is used as a sputter gas to generate a plasma in the sputter chamber and to vent the chamber.

The Sputter coater 04 (Agar Scientific) is located in the cleanroom Cx1.

The user manual and contact information can be found in LabManager:

Sputter coater 04

Process knowledge

Deposition of gold

Overview of the performance of the Sputter coater 04 (Agar Scientific) and some process related parameters

Purpose		Gold sputter coating of different samples before SEM characterization
Performance	Film thickness	Not measured.
Performance	Deposition rate	Not measured
Process parameter range	Pressure	0.01 mbar (default value)
	Current	40 mA (default value)
	Sputter time	Maximum 30 s
Substrates	Batch size	One sample smaller than a 100 mm wafer Several smaller samples
Substrates	Allowed materials	All samples that are allowed in the SEM Supra's

Revision as of 14:47, 6 February 2017 view source Mdyma (talk \| contribs) danchip 584 edits No edit summary ← Older edit		Revision as of 14:50, 6 February 2017 view source Mdyma (talk \| contribs) danchip 584 edits →‎The Sputter coater 03 (Cressington) Newer edit →
Line 136:		Line 136:
	Argon is used as a sputter gas to generate a plasma in the sputter chamber and to vent the chamber.		Argon is used as a sputter gas to generate a plasma in the sputter chamber and to vent the chamber.

	The ~~Balzer sputter~~ coater is located in the 346 basement, room 907 (next to the SEM Supra 1) .		The Sputter coater 03 (Cressington) is located in the 346 basement, room 907 (next to the SEM Supra 1) .