Specific Process Knowledge/Characterization/AFM: Atomic Force Microscopy/Workspaces: Difference between revisions
No edit summary |
|||
| Line 73: | Line 73: | ||
! SEM images | ! SEM images | ||
|- | |- | ||
|Box1 no. 1||bghe||A lot of triangles in the image|| | |Box1 no. 1||bghe||A lot of triangles in the image||[[File:Box1 no1 tilt0_26.jpg|200px]][[File:Box1 no1 tilt0ny2_56.jpg|200px]] | ||
|- | |- | ||
|Box1 no. 2||bghe/smurthy||Round pillars became misshaped | |Box1 no. 2||bghe/smurthy||Round pillars became misshaped||[[File:Box1 no2 tilt0ny2_55.jpg|200px]][[File:Box1 no2 tilt21_04.jpg|200px]] | ||
|- | |- | ||
|Box1 no. 3||bghe/zhongli||Force curve bad, could not get the tip off the surface | |Box1 no. 3||bghe/zhongli||Force curve bad, could not get the tip off the surface | ||
Revision as of 13:23, 27 July 2015
Feedback to this page: click here
What scanning mode, experiment/workspace and probe should I select
| Roughness measurements | Topographic measurements with no steep/abrupt steps | Steep/abrupt steps but no high aspect ratio | High aspect ratio measurements | |
|---|---|---|---|---|
| Recommended mode | Roughness measurement can be done in both Contact, Tapping and ScanAsyst mode. We recommend ScanAsyst mode because of less chance of (non-uniform) deformation of the sample and less tip wear - and because of ease of use. | For Topographic measurements with no steep/abrupt steps we also recommend ScanAsyst mode due to less chance of (non-uniform) deformation of the sample and less tip wear - and because of ease of use. | For Steep/abrupt steps but no high aspect ratio structures we still recommend ScanAsyst mode due to ease of use and lower top wear. | For High aspect ratio measurements we recommend Tapping mode. There is not yet a ScanAsyst probe developed for high aspect ratio. Therefore we recommend Tapping mode. |
| Recommended probes | ScanAsyst in air | ScanAsyst in air | ScanAsyst in air for ScanAsyst mode
TAP300Al-G for Tapping mode |
AR5T-NCHR |
| Recommended experiment/Workspace |
QNM in air* |
QNM in air* |
QNM in air* | TappingMode 300nm trench (for steps <~1µm)
Tappping mode in air - 6µm Deep Trench (for steps >1~µm) |
*By choosing the work space/experiment QNM in air (Mechanical properties - QNM in air) scanAsyst is included and so are the nanomechanical properties like modulus, adhesion, dissipation and deformation.
More information about de different modes
Contact, Tapping and Peak Force Tapping
Please flowing this link to Brukers homepage: Introduction_to_Brukers_ScanAsyst_and_PeakForce_Tapping_Atomic_Force_Microscopy_Technology_AFM_AN133.pdf
PeakForce tapping and quantitative nanomechanical mapping
Please flowing this link to Brukers homepage: PeakForce tapping and Nanomechanical option
Peak Force KPFM (Kelvin Probe Force Microscopy)
Please flowing this link to Brukers homepage: pf-kpfm.html
Evaluation of used probes
| Box number and probe number | User Initials | Explanation | SEM images |
|---|---|---|---|
| Box1 no. 1 | bghe | A lot of triangles in the image |  
|
| Box1 no. 2 | bghe/smurthy | Round pillars became misshaped |  
|
| Box1 no. 3 | bghe/zhongli | Force curve bad, could not get the tip off the surface | |
| Box1 no. 4 | mattod | Used dirty sample, force curve very bad, tip probably broken | |
| Box1 no. 5 | mattod | Tip broken during tip change | |
| Box1 no. 6 | abshir | Bad force curve (fluctuates) | |
| Box1 no. 7 | bghe | Was OK on large structures but they got larger | |
| Box1 no. 8 | mattod | Bad force curve | |
| Box1 no. 9 | kabi | Blunt tip . Definitely (triangles) | |
| Box1 no. 10 | kabi | Blunt tip. Definitely (triangles) | |
| Box2 no. 1 | mattod | Bad force curve | |
| Box2 no. 2 | mattod | Broken tip |