Specific Process Knowledge/Etch/ICP Metal Etcher/silicon/nano/Sinan33: Difference between revisions
Created page with "== The Sinano3.3 recipe == {| border="2" cellpadding="2" cellspacing="1" |+ '''Recipe Sinano3.3''' |- ! rowspan="6" align="center"| Recipe | Gas | BCl<sub>3</sub> 5 sccm, HB..." |
No edit summary |
||
| (5 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
<!--Checked for updates on 10/7-2019 - ok/jmli --> | |||
<!-- Ok, jmli 20170627 --> | |||
<!--Checked for updates on 24/8-2021. ok/ jmli--> | |||
<!--Checked for updates on 4/4-2025 - ok/jmli --> | |||
== The Sinano3.3 recipe == | == The Sinano3.3 recipe == | ||
<!-- revised 1/6-2015 by jmli --> | |||
{| border="2" cellpadding="2" cellspacing="1" | {| border="2" cellpadding="2" cellspacing="1" | ||
|+ '''Recipe Sinano3.3''' | |+ '''Recipe Sinano3.3''' | ||
| Line 31: | Line 36: | ||
|- | |- | ||
| Mask | | Mask | ||
| 180 nm zep etched down to 64 nm | | The [[Specific Process Knowledge/Etch/ICP Metal Etcher/silicon/nano/nanoetch/180nmzep|180 nm zep resist]] etched down to 64 nm | ||
|- | |- | ||
|} | |} | ||
Latest revision as of 07:36, 4 April 2025
The Sinano3.3 recipe
| Recipe | Gas | BCl3 5 sccm, HBR 15 sccm |
|---|---|---|
| Pressure | 2 mTorr, Strike 3 secs @ 5 mTorr | |
| Power | 900 W CP, 75 W PP | |
| Temperature | 20 degs | |
| Hardware | 100 mm Spacers | |
| Time | 180 secs | |
| Conditions | Run ID | 430, 4325 ID |
| Conditioning | Sequence: Oxygen clean, MU tests, processes, no oxygen between runs | |
| Mask | The 180 nm zep resist etched down to 64 nm |
- The results of the Sinano3.3 recipe
-
The 30 nm trenches -
The 60 nm trenches -
The 90 nm trenches -
The 120 nm trenches -
The 150 nm trenches
| Nominal trench line width | ' | ' | 30 | 60 | 90 | 120 | 150 | Average | Std. dev. |
| Etch rate | nm/min | 71 | 101 | 114 | 120 | 122 | 105 | 21 | |
| Sidewall angle | degs | 82 | 82 | 81 | 82 | 81 | 82 | 1 | |
| CD loss | nm/edge | -4 | -2 | -2 | -5 | 5 | -2 | 4 | |
| CD loss foot | nm/edge | -4 | 7 | 13 | 13 | 25 | 11 | 11 | |
| Bowing | 10 | 11 | 10 | -2 | 1 | 6 | 6 | ||
| Bottom curvature | -27 | 0 | -17 | -6 | -5 | -11 | 11 | ||
| Zep etch rate | 51 |