Specific Process Knowledge/Characterization/Topographic measurement

Feedback to this page: click here

Topographic measurements

Topographic measurements are measurements of height differences on your sample. If you measure many spots on the sample you can get a topographic image of the surface.

At DTU Nanolab we have eight systems for topographic measurements:

• Dektak stylus profilers (Dektak XTA, Dektak 8, Dektak 150 and Dektak 3ST) - Profilers for measuring micro structures
• Optical profilers (Optical profiler Sensofar and Optical profiler Filmetrics) - 3D Profilers for measuring micro structures
• AFMs (AFM Icon-PT1 and AFM Icon-PT2) - AFMs for measuring nano structures

High Aspect ratio structures

The fact that the stylus tip of a Dektak profilers or an AFM is shaped like a cone with some finite tip angle causes a problem when characterizing high aspect ratio structures. For instance, if a 20 µm wide trench is etched deeper than approximately 18 µm, the tip of the Dektak will not be able to reach the bottom. The optical profiler uses a light beam that is focused through an objective. Therefore it is able to measure higher aspect ratios. The aspect ratio is limited by the possibility for the light to reach the bottom and get back to the detector. On some samples we have been able to measure aspect ratios above 1:10. Otherwise the solution is to cleave the sample along a line that is perpendicular to the trench and then inspect the profile in a scanning electron microscope or a microscope (for large structures).

Thin film thickness

The profilers can be used to measure the thickness of optically transparent thin films or etched non-transparent thin films. There are also other options for measuring film thickness. All the methods are compared on the "Measurement of thin film thickness and optical constants" page

Comparison of stylus profilers, optical profilers and AFMs at Nanolab

	P17 stylus profiler	Dektak XTA stylus profiler	Optical Profiler (Sensofar)	Optical Profiler (Filmetrics)	AFM Icon 1 and AFM Icon 2	Dektak 150 stylus profiler	Dektak 3ST stylus profiler
Generel description	Profiler for measuring microstructures. Can do wafer mapping, roughness measurements and stress measurements.	Profiler for measuring microstructures. Can do wafer mapping and stress measurements.	3D Profiler for measuring microstructures and surface roughness. Can do wafer mapping.	3D Profiler for measuring microstructures and surface roughness. Can do wafer mapping. Located in the basement.	AFM for measuring nanostructures and surface roughness	Profiler for measuring microstructures. Located in Pack Lab.	Profiler for measuring microstructures. Located in the basement.
Max. scan range xy	Line scan x: 1 µm to 200mm	Line scan x: 50µm to 55mm in one scan. Maximum scan length with stitching 200mm.	Depending on the objective: One view: 127µmX95µm to 1270µmX955µm Stitching: In principel a whole 6" wafer (time consuming)	Only 10x objective: 2.0 mm x 1.7 mm	90 µm square	Line scan x: 50-55000 µm	Line scan x: 50-50000 µm
Max. scan range z	up to 900 µm	50 Å to 1 mm	Depending on the objective and Z resolution: 94.4 µm ->9984 µm	10 mm (piezo range 500 µm)	1 µm (can go up to 5 µm under special settings)	50 Å to 1 mm	100 Å to 130 nm
Resolution xy	down to 0.025 µm	down to 0.003 µm	Depending on the objective: 0.5µm -> 5µm	Resolving power og the lense: 0.92 µm	Depending on scan size and number of samples per line and number of lines - accuracy better than 2%	down to 0.003 µm	down to 0.5 µm
Resolution z	0.01, 0.08 or 0.6 Å depending on range (according to manufacturer)	1 Å, 10 Å, 40 Å or 160 Å depending on range	Depending on measuring methode: PSI down to 0.01 nm VSI down to 1 nm Confocal (depending on objective): 1nm -> 50nm	Accuracy 0.7% Precision 0.1%	<1Å - accuracy better than 2%	1 Å, 10 Å or 20 Å depending on range	1 Å, 10 Å, 40 Å or 160 Å depending on range
Max. scan depth [µm] as a function of trench width W)	1.2*(W[µm]-5µm)	1.2*(W[µm]-5µm)	Depending on material and trench width: Somewhere between 1:1 and 1:12	Depending on material and trench width.	~1:1 with standard cantilever.	1.2*(W[µm]-5µm)	1.2*(W[µm]-2.5µm)
Standard tip radius	5 µm 45o cone	5 µm 45o cone	No tip - using light Blue monochromatic LED: 460nm White broadband LED: 550nm	No tip - using light Blue monochromatic LED: 460nm White broadband LED: 550nm	<12 nm on standard cantilever	5 µm 45o cone	2.5 µm 45o cone
Stress measurement	Can be done	Can be done	No stress calculation capability	Cannot be done	Cannot be done	Cannot be done	Cannot be done
Surface roughness	Can be done on a line scan	Can be done on a line scan	Can be done on a line or an area	Can be done on a line or an area	Can be done on a selected surface area	Can be done on a line scan	Recommended to use Dektak XTA or Dektak 8.
Substrate size	up to 8"	up to 6"	Up to more than 6"	100x100 mm	6" or less	up to 6"	4" or less
Allowed materials	Almost any material that does not leave residual on the stage, please check the responsible group for any non standard materials	Almost any material that does not leave residual on the stage, please check the responsible group for any non standard materials	Almost any material that does not leave residual on the stage, please check the responsible group for any non standard materials	Almost any material that does not leave residual on the stage, please check the responsible group for any non standard materials	Almost any material that does not leave residual on the stage, please check the responsible group for any non standard materials	Almost any material that does not leave residual on the stage.	Almost any material that does not leave residual on the stage.
Location	Cleanroom F-2	Cleanroom F-2	Cleanroom F-2	Basement, building 346, room 904	AFM Icon1: Cleanroom C-1 AFM Icon2: Basement, building 346, room 904	Basement, building 346, room 904	Pack-lab, building 347, room 179