Specific Process Knowledge/Lithography/DUVStepperLithography

DUV Stepper

DUV Stepper is placed in F-3

Feedback to this section: click here

The deep-UV stepper FPA-3000EX4 from Canon is an advanced exposure system designed for mass-production of 6 and 8 inch wafers/ devices having a throughput of up to 90 wafers per hour. The largest applicable thickness of the wafers/ devices is 1,2 mm. Also 4" wafers/ devices can be processed with some restrictions concerning throughput, resolution, uniformity and maximum allowed wafer thickness. The system is equipped with a KrF Excimer laser from Cymer (wavelength 248 nm). Its projection lens’ NA is variable over a range between 0,4 and 0,6. Additionally, the partial coherence factor (σ) of the illumination system can be adjusted and different off-axis illumination modes can be selected.

The critical dimension (CD) of patterns that can be realized is specified at around 250nm for arbitrary formed patterns in the standard illumination mode (NA=0,6; σ =0,65). However, the best achievable resolution is different for each pattern type, pattern shape and pitch. So linewidths down to 160 nm could be achieved for geometrically simple patterns or pattern arrays (single and multiple line or pin-hole structures).

The user manual(s), quality control procedure(s) and results and contact information can be found in LabManager: Equipment info in LabManager

Process information

• Optimization and Simulation
• Reticle Design
• Process Flow

• The SÜSS Spinner-Stepper is dedicated for spinning DUV resists. Please note that a Bottom Anti-Reflective Coating (BARC) is necessary to guarantee high quality of both the resist film and the exposure. Please find the specification of the SÜSS Spinner-Stepper in the LabAdviser [Spinner-Stepper].

• Usually, in order to guarantee the highest fidelity of the produced pattern on the wafer the best suitable exposure dose has to be evaluated for each individual pattern, resist type and resist thickness. Thus, when a new reticle is used, it is recommended to perform an exposure dose test and - for resist thicknesses larger than 500 nm - additionally a focus offset test. After evaluation by SEM the identified dose and focus offset - that leads to the most accurate pattern - can be applied in the DUV process for the required wafers.

• The DUV process - including BARC and resist spinning, exposure, post exposure bake and development - will be performed by the customer together with the Photolith group of Danchip. Any kind of inspection, evaluation and pre- and post-processing should be performed by the customer.

Equipment performance and process related parameters

Purpose		Exposure system designed for mass/production of devices with linewidth down to 250nm
Specifications	Magnification	1:5
	Projection lens Numerical Aperture	0,4 - 0,60
	Illumination system's σ	0,2 - 0,75 (standard illumination mode: σ = 0,65)
	Exposure source	KrF laser
	Wavelength	248nm
	Illumination intensity	2800 W/m2
	Illumination uniformity	1,2%
	Maximum printed field size	22 x 26 mm (maximum on wafer)
	Alignment accuracy	3 sigma = 50 nm
Substrates	Substrate size	100 mm wafers 150 mm wafers 200 mm wafers
	Allowed materials	Any standard cleanroom material
	Batch	1 - 25

SÜSS Spinner-Stepper

The SÜSS Spinner-Stepper is placed in F-3

Feedback to this section: click here

This spinner is dedicated for spinning DUV resists. The spinner is fully automatic and can run up to 25 substrates in a batch 4", 6", and 8" size. The machine is equipped with the 3 resist lines, an automatic syringe system and a solvent line for cleaning and back-side rinse.

The user manual(s), quality control procedure(s) and results and contact information can be found in LabManager: Equipment info in LabManager

Process information

The spinning process will be performed by the customer together with the Photolith group of Danchip. In case you would like to do DUV lithography please contact Lithography team, who will consult you and run your wafers together with you.

Information about resist can be found here:

• Bottom Anti Reflection Coating (BARC) DUV 42S-6 .
• Datasheet DUV42S-6.
• Positive DUV resist for spinning in 300-600nm thickness range KRF M230Y.
• Positive DUV resist for spinning in 1600-800nm thickness range KRF M35G.
• Negative DUV resist for spinning in 1400-800nm or diluted with EC Solvent in 1:1 in 400-200nm thickness range UVN2300-0.8.

Equipment performance and process related parameters

Purpose		Spin coating and soft baking of BARC Spin coating and soft baking of DUV resists Post exposure baking
Resist		BARC DUV42S-6 Positive tone resist KRF M230Y Positive tone resist KRF M35G Negative tone resist UVN2300-0.8
Performance	Coating thickness	BARC DUV42S-6 around 60nm Positive tone resist KRF M230Y 300-600nm Positive tone resist KRF M35G 800-1600nm Negative tone resist UVN2300-0.8 200-1400nm
Process parameters	Spin speed	10 - 5000 rpm
	Spin acceleration	100 - 10000 rpm/s
	Hotplate temperature	175°C for BARC baking 130°C for positive tone resist soft baking and post exposure baking 100°C for negative tone resist soft baking and post exposure baking
Substrates	Substrate size	100 mm wafers 150 mm wafers 200 mm wafers
	Allowed materials	Any standard cleanroom material
	Batch	1 - 25

Developer TMAH Stepper

The Developer-TMAH-Stepper is placed in F-3

Feedback to this section: click here

This developer is dedicated for development of DUV resists. The developer is fully automatic and can run up to 25 substrates in a batch 4", 6", and 8" size. The machine is equipped with 1 developer line, in our case in 2,38% water based TMAH, 1 topside rinse line with water, 1 backside rinse line with water and 1 N2 line for drying.

The user manual(s), quality control procedure(s) and results and contact information can be found in LabManager: Equipment info in LabManager

Process information

The SEM picture of 250nm pillors and lines. Exposure dose is 140 J/m2.

The spinning process will be performed by the customer together with the Photolith group of Danchip. In case you would like to do DUV lithography please contact Lithography team, who will consult you and run your wafers together with you.

Here you can find a chart‎ demonstrating a dependence between 250nm line width/pillors diameter and exposure dose.

Equipment performance and process related parameters

Purpose		Development of DUV resist: KRF 230Y and KRF M35G
Developer		2,38% water based TMAH
Process parameters	Spin speed	10 - 5000 rpm
	Spin acceleration	100 - 10000 rpm/s
	Hotplate temperature	130°C for post exposure baking
Substrates	Substrate size	100 mm wafers 150 mm wafers 200 mm wafers
	Allowed materials	Any standard cleanroom material
	Batch	1 - 25