Specific Process Knowledge/Etch/Etching of Silicon: Difference between revisions
Line 9: | Line 9: | ||
==Comparison of KOH etch, wet PolySilicon etch, RIE etch and ASE etch for etching of Silicon== | ==Comparison of KOH etch, wet PolySilicon etch, RIE etch and ASE etch for etching of Silicon== | ||
{| border=" | {| border="2" cellspacing="0" cellpadding="5" align="center" | ||
! | ! | ||
! KOH | ! KOH | ||
Line 15: | Line 15: | ||
! RIE | ! RIE | ||
! ASE | ! ASE | ||
|- | |- valign="top" | ||
|General description | |'''General description''' | ||
| | | | ||
*Anisotropic etch in the (100)-plan | *Anisotropic etch in the (100)-plan | ||
Line 28: | Line 28: | ||
*As RIE but better for high aspect ratio etching and deep etches (higher etch rate) | *As RIE but better for high aspect ratio etching and deep etches (higher etch rate) | ||
*Good selectivity to photoresist | *Good selectivity to photoresist | ||
|- | |-valign="top" | ||
|Possible masking materials | |'''Possible masking materials''' | ||
| | | | ||
*Silicon Nitride | *Silicon Nitride | ||
Line 48: | Line 48: | ||
*Silicon Nitride | *Silicon Nitride | ||
*Aluminium | *Aluminium | ||
|- | |- valign="top" | ||
|Etch rate | |'''Etch rate''' | ||
| | | | ||
*Si(100) @80<sup>o</sup>C: 1.29+0.05 µm/min | *Si(100) @80<sup>o</sup>C: 1.29+0.05 µm/min | ||
Line 56: | Line 56: | ||
| | | | ||
*~100-200 nm/min, highly dependent on doping level | *~100-200 nm/min, highly dependent on doping level | ||
|<40nm/min to >600nm/min depending on recipe parameters and mask design | | | ||
|<130nm/min to >5.6 µm/min depending on recipe, mask design and aspect ratio. | *<40nm/min to >600nm/min depending on recipe parameters and mask design | ||
|- | | | ||
|Size of substrate | *<130nm/min to >5.6 µm/min depending on recipe, mask design and aspect ratio. | ||
|-valign="top" | |||
|'''Size of substrate''' | |||
| | | | ||
*4" in our standard bath | *4" in our standard bath | ||
*4", 2" in "Fumehood KOH" | *4", 2" in "Fumehood KOH" | ||
| | |||
*4" in our standard bath | |||
|4" (or smaller with carrier) | | | ||
|6" (when it is set up for 6") and 4" (or smaller if you have a carrier) | *4" (or smaller with carrier) | ||
|- | | | ||
|Batch size | *6" (when it is set up for 6") and 4" (or smaller if you have a carrier) | ||
|-valign="top" | |||
|'''Batch size''' | |||
| | | | ||
*25 wafers at a time | *25 wafers at a time | ||
*1-5 wafers in "Fumehood KOH" | *1-5 wafers in "Fumehood KOH" | ||
|25 wafers at a time | | | ||
|One wafer at a time | *25 wafers at a time | ||
|One wafer at a time | | | ||
|- | *One wafer at a time | ||
|Allowed materials | | | ||
*One wafer at a time | |||
|-valign="top" | |||
|'''Allowed materials''' | |||
| | | | ||
*Silicon | *Silicon |
Revision as of 13:24, 31 January 2008
Etch of silicon can be done by either wet etch or dry etch. The standard setups for this here at DANCHIP are:
Wet etches:
Dry etches:
Comparison of KOH etch, wet PolySilicon etch, RIE etch and ASE etch for etching of Silicon
KOH | PolySilicon etch | RIE | ASE | |
---|---|---|---|---|
General description |
|
|
|
|
Possible masking materials |
|
|
|
|
Etch rate |
|
|
|
|
Size of substrate |
|
|
|
|
Batch size |
|
|
|
|
Allowed materials |
|
|
|
|