Latest revision as of 09:44, 6 June 2023

Feedback to this page: click here

Unless otherwise stated, this page is written by DTU Nanolab internal

Silicon sputtering in the Wordentec

Silicon can be sputter deposited in the Wordentec as well as in the Sputter-System(Lesker) (details on sputtering Si in the Sputter-System Lesker here) and in the new Cluster Lesker (results here and here).

Parameters

Listed below are tried parameters, that can be used during Si deposition in the Wordentec. The process parameters in the table below can be used as started values, run a test process to be sure that you get the right thickness.

Do not use the power more than 180 W without consulting staff, since the Si target could break into a lot of small pieces.

	Settings 1	Settings 2
Process type	Sputtering	Sputtering
Power	130W	170W
Sputter pressure	5*10^-3 mbar	1*10^-2 mbar
Rate	About 0.7 Å/s	About 0.6 Å/s

In November 2018 Rebecca Ettlinger and Patama Pholprasit tested Si sputter deposition in the Wordentec at 500 W with a low sputter pressure of 2*10^-3 mbar together with Yannick Seis. The aim was a better uniformity of the sputtered film. See details in the Wordentec Process log.

It is thus possible to use a higher power together with a lower pressure, but please do not do this without consulting the [Thin Film group].

@@ Line 1: / Line 1: @@
 '''Feedback to this page''': '''[mailto:labadviser@nanolab.dtu.dk?Subject=Feed%20back%20from%20page%20http://labadviser.labadviser.dtu.dk/index.php/Specific_Process_Knowledge/Thin_film_deposition/Si_sputter_in_Wordentec click here]'''
-== Silicon sputter==
+<i> Unless otherwise stated, this page is written by <b>DTU Nanolab internal</b></i>
-Silicon can be sputter deposited in the [[Specific Process Knowledge/Thin film deposition/Wordentec|Wordentec.]]
+= Silicon sputtering in the Wordentec=
+Silicon can be sputter deposited in the [[Specific Process Knowledge/Thin film deposition/Wordentec|Wordentec]] as well as in the [[Specific Process Knowledge/Thin film deposition/Lesker|Sputter-System(Lesker)]] (details on sputtering Si in the Sputter-System Lesker [[Specific Process Knowledge/Thin film deposition/Deposition of Silicon/Si sputter in Sputter-System Lesker|here]]) and in the new [[Specific Process Knowledge/Thin film deposition/Cluster-based multi-chamber high vacuum sputtering deposition system|Cluster Lesker]] (results [[Specific Process Knowledge/Thin film deposition/Deposition of Silicon/Si sputter in Sputter-System Metal-Oxide(PC1)|here]] and [[Specific Process Knowledge/Thin film deposition/Deposition of Silicon/Si sputter in Sputter-System Metal-Oxide(PC3)|here]]).
-'''Parameters'''
-Listed below are tried parameters, that can be used during deposition. The process parameters in the table below can be used as started values, run a test process to be sure that you get the right thickness.
+==Parameters==
+Listed below are tried parameters, that can be used during Si deposition in the Wordentec. The process parameters in the table below can be used as started values, run a test process to be sure that you get the right thickness.
 '''Do not use the power more than 180 W without consulting staff''', since the Si target could break into a lot of small pieces.
@@ Line 38: / Line 40: @@
 |}
-In November 2018 Rebecca Ettlinger and Patama Pholprasit tested Si sputter deposition in the Wordentec at 500 W with a low sputter pressure of 2*10<sup>-3</sup> mbar together with Yannick Seis. The aim was a better uniformity of the sputtered film. See details in the process log. It is thus possible to use a higher power together with a lower pressure, but please do not do this without consulting the Thin Film group.
+In November 2018 Rebecca Ettlinger and Patama Pholprasit tested Si sputter deposition in the Wordentec at '''500 W with a low sputter pressure of 2*10<sup>-3</sup> mbar''' together with Yannick Seis. The aim was a better uniformity of the sputtered film. See details in the [http://labmanager.dtu.dk/function.php?module=Processlog&view=editlog&machid=167 Wordentec Process log].
+It is thus possible to use a higher power together with a lower pressure, but please do not do this without consulting the [[mailto:thinfilm@nanolab.dtu.dk Thin Film group]].