Specific Process Knowledge/Etch/Etching of TOPAS: Difference between revisions
No edit summary |
No edit summary |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
<!--Checked for updates on 3/2-2016 - ok/jmli --> | <!--Checked for updates on 3/2-2016 - ok/jmli --> | ||
<!--Page reviewed by jmli 9/8-2022 --> | |||
'''Feedback to this page''': '''[mailto:labadviser@nanolab.dtu.dk?Subject=Feed%20back%20from%20page%20http://labadviser.nanolab.dtu.dk/index.php/Specific_Process_Knowledge/Etch/Etching_of_TOPAS click here]''' | '''Feedback to this page''': '''[mailto:labadviser@nanolab.dtu.dk?Subject=Feed%20back%20from%20page%20http://labadviser.nanolab.dtu.dk/index.php/Specific_Process_Knowledge/Etch/Etching_of_TOPAS click here]''' | ||
<!--Page reviewed by jmli 9/8-2022 --> | |||
==Etching of TOPAS== | ==Etching of TOPAS== | ||
| Line 6: | Line 9: | ||
{| border="2" cellpadding="2" cellspacing="1" style="text-align:center;" | {| border="2" cellpadding="2" cellspacing="1" style="text-align:center;" | ||
|+ '''TOPAS''' by khara@ | |+ '''TOPAS''' by khara@anolab | ||
|- | |- | ||
! Parameter | ! Parameter | ||
| Line 46: | Line 49: | ||
==Under etching and local masking== | ==Under etching and local masking== | ||
When etching TOPAS I have in general used a hard mask material underneath my layer of | When etching TOPAS I have in general used a hard mask material underneath my layer of photoresist, to ensure that if the resist was completely removed, a mask was still present. It is however always recommended to have a photoresist as mask, as a hard mask material will introduce roughness in unmask areas of the polymer. | ||
| Line 56: | Line 59: | ||
|[[Image:TOPAS-Al-hard-mask_U33.jpg|200x200px]] | |[[Image:TOPAS-Al-hard-mask_U33.jpg|200x200px]] | ||
|- | |- | ||
|style="width:200px;" |Etch broke through the | |style="width:200px;" |Etch broke through the photoresist layer, and sputtered silicon have redeposited on the polymer surface, introducing local masking effects. | ||
|style="width:200px;" |The aluminum hard mask has been etched in the resist developer introducing poor edge definition even though the resist was not completely removed by the etch. | |style="width:200px;" |The aluminum hard mask has been etched in the resist developer introducing poor edge definition even though the resist was not completely removed by the etch. | ||
|- | |- | ||
Latest revision as of 10:14, 9 August 2022
Feedback to this page: click here
Etching of TOPAS
TOPAS is etched by an oxygen plasma in the ASE. Masking of TOPAS was achieved by photo resist or a hard mask of aluminum or silicon. Photo resist is the preferred masking material, since hard masks tends to introduce local masking due to redeposition. TOPAS can be etched at rates up to 500 nm/min, with excellent uniformity over the wafer.
| Parameter | Slow TOPAS etch | Fast TOPAS etch |
|---|---|---|
| O2 (sccm) | 50 | 99 |
| CO2 (sccm) (not available anymore) | 50 | 0 |
| Pressure (mTorr) | 40 | 40 |
| Coil power (W) | 800 | 720 |
| Platen power (W) | 60 | 60 |
| Temperature (oC) | 20 | 20 |
| Etch rate (nm/min) | ~350 | ~500 |
| Center-Edge uniformity | 0.98 | 0.95 |
Under etching and local masking
When etching TOPAS I have in general used a hard mask material underneath my layer of photoresist, to ensure that if the resist was completely removed, a mask was still present. It is however always recommended to have a photoresist as mask, as a hard mask material will introduce roughness in unmask areas of the polymer.
| Silicon hard mask | Aluminum hard mask |
|---|---|
|
|
| Etch broke through the photoresist layer, and sputtered silicon have redeposited on the polymer surface, introducing local masking effects. | The aluminum hard mask has been etched in the resist developer introducing poor edge definition even though the resist was not completely removed by the etch. |
Etch
|
Etch
|