Specific Process Knowledge/Bonding/Fusion bonding: Difference between revisions

From LabAdviser
← Older edit
VisualWikitext
Taran (talk | contribs)
DCH-Employees-701, NLAB-Employees-701, NLAB-LabmanagerAllUsers, NLAB-Nlab307-labadviser-users-34891
3,292 edits
Sifkle (talk | contribs)
NLAB-Employees-701, NLAB-LabmanagerAllUsers
55 edits
No edit summary
 
(2 intermediate revisions by 2 users not shown)
Line 1: Line 1:
'''Feedback to this page''': '''[mailto:photolith@danchip.dtu.dk?Subject=Feed%20back%20from%20page%20http://labadviser.danchip.dtu.dk/index.php/Specific_Process_Knowledge/Bonding/Fusion_bonding click here]'''
'''Feedback to this page''': '''[mailto:photolith@Nanolab.dtu.dk?Subject=Feed%20back%20from%20page%20http://labadviser.nanolab.dtu.dk/index.php/Specific_Process_Knowledge/Bonding/Fusion_bonding click here]'''
 
'''Unless anything else is stated, everything on this page, text and pictures are made by DTU Nanolab.'''


==Fusion Bonding==
==Fusion Bonding==


Fusion bonding is a relative weak bond between e.g. two clean Si wafers. It is absolutely necessary for the wafers to be very clean and to be annealed at 1000°C afterwards to avoid and minimize defects. Fusion bonding can be made as a Si to Si direct bonding or with SiO<math>_2</math> layers in between. It is also possible to use nitride in between but it should be close to 100% particle free. We have good experience with Sintef but unfortunately not with the old DANCHIP nitride furnace.   
Fusion bonding is a relative weak bond between e.g. two clean Si wafers. It is absolutely necessary for the wafers to be very clean and to be annealed at 1000°C afterwards to avoid and minimize defects. Fusion bonding can be made as a Si to Si direct bonding or with SiO<math>_2</math> layers in between. It is also possible to use nitride in between but it should be close to 100% particle free. We have good experience with Sintef but unfortunately not with the old DTU Nanolab nitride furnace.   
 
Please be advised that it is notoriously difficult to use the EVG NIL bond aligner, due to its manual nature it is strongly advised to book extra time to do alignment. However alignment of &plusmn;2 microns is possible by very experienced users. The alignment marks (on the masks) are to be positioned at y=0 and x=&plusmn;40mm for 4", for optimal result. It is possible to use both backside alignment and IR alignment however IR alignment is more accurate, since only one aligning is used. However it is very important to use dobbelt polished wafers to have enough IR light to see the patterns. 


Try and put a fusion bonding as early in a process sequence as possible, since during annealing is not possible to have any kind of metals on your wafer. Furthermore the thermal budget could drive dopants further into the wafer than wanted.
Try and put a fusion bonding as early in a process sequence as possible, since during annealing is not possible to have any kind of metals on your wafer. Furthermore the thermal budget could drive dopants further into the wafer than wanted.
===Bonding procedure===
*'''Remember to use double side polished wafers for IR alingment.'''
*Clean the wafers with [[Specific Process Knowledge/Wafer cleaning/IMEC|IMEC]] clean.
*Transport the wafers to the bonder in a clean box.
*Clean the chuck with ethanol.
*Clean the glass top with ethanol.
*Clean the graphite electrode with ethanol.
*Clean the bond glass with Ethanol.
*Place the wafers in the aligner with a clean tweezer.
*Align the wafers
*Place the chuck and graphite electrode in the chamber.
*Close the chamber.
*Turn the µm screw on top of the chamber to set the desired stack height.
*After pre bonding in the EVG NIL the wafers are to be annealed in the bond furnace (C3) at 1000<sup>o</sup>C.

Latest revision as of 07:24, 6 February 2023

Feedback to this page: click here

Unless anything else is stated, everything on this page, text and pictures are made by DTU Nanolab.

Fusion Bonding

Fusion bonding is a relative weak bond between e.g. two clean Si wafers. It is absolutely necessary for the wafers to be very clean and to be annealed at 1000°C afterwards to avoid and minimize defects. Fusion bonding can be made as a Si to Si direct bonding or with SiO layers in between. It is also possible to use nitride in between but it should be close to 100% particle free. We have good experience with Sintef but unfortunately not with the old DTU Nanolab nitride furnace.

Try and put a fusion bonding as early in a process sequence as possible, since during annealing is not possible to have any kind of metals on your wafer. Furthermore the thermal budget could drive dopants further into the wafer than wanted.

Retrieved from "https://labadviser.nanolab.dtu.dk//index.php?title=Specific_Process_Knowledge/Bonding/Fusion_bonding&oldid=44359"