Jump to content

Specific Process Knowledge/Lithography/EBeamLithography/JEOLJobPreparation: Difference between revisions

← Older edit
VisualWikitext
Thope (talk | contribs)
DCH-Employees-701, NLAB-Employees-701, NLAB-LabmanagerAllUsers, NLAB-Nlab347-labadviser-users-35231
2,178 edits
Elelop (talk | contribs)
NLAB-Employees-701, NLAB-LabmanagerAllUsers, NLAB-Nlab307-labadviser-users-34891, NLAB-Nlab347-labadviser-users-35231
26 edits
 
(12 intermediate revisions by one other user not shown)
Line 37: Line 37:


In the following we will discuss details of the most commonly used commands in the SDF and JDF and provide example files for various types of jobs. We will start with a simple exposure without pattern alignment, i.e. a first print exposure. In JEOL terminology this is called “mask exposure mode” whereas exposure with alignment is refered to as “direct exposure mode”.
In the following we will discuss details of the most commonly used commands in the SDF and JDF and provide example files for various types of jobs. We will start with a simple exposure without pattern alignment, i.e. a first print exposure. In JEOL terminology this is called “mask exposure mode” whereas exposure with alignment is refered to as “direct exposure mode”.
Templates for SDF and JDF files can be found on the Cleanroom drive here: O:\CleanroomDrive\_JEOL9500Training\Templates


=First print - mask exposure mode=
=First print - mask exposure mode=
Line 51: Line 53:
ACC 100                       
ACC 100                       
CALPRM '2na_ap4'             
CALPRM '2na_ap4'             
DEFMODE 2                    
DEFMODE 2  
FFOCUS                   
RESIST 240                     
RESIST 240                     
SHOT A,16                       
SHOT A,16                       
Line 90: Line 93:


This parameter determines if the system writes in 2 deflector mode or 1 deflector mode. In 2 deflector mode the primary deflector positions the beam within the main writing field with the subdeflector positions the beam with each 4 x 4 µm subfield. Writing speed is significantly higher in 2 deflector mode and the system should always be used in mode 2.
This parameter determines if the system writes in 2 deflector mode or 1 deflector mode. In 2 deflector mode the primary deflector positions the beam within the main writing field with the subdeflector positions the beam with each 4 x 4 µm subfield. Writing speed is significantly higher in 2 deflector mode and the system should always be used in mode 2.
'''FFOCUS'''
Field Focus was added to the system in 2021. It allows the system to adjust beam focus individually for each writing field based on a sample surface height map generated with HEIMAP. If FFOCUS is omitted the HEIMAP matrix will be used to calculated a single average sample height and beam focus will be set to this value. If FFOCUS is used the HEIMAP data will be used to generate a surface map and each individual writing field will be exposed with a beam focus based on this surface map. This function can not be used with height data obtained from SETWFR or CHIPAL.


'''RESIST [dose]'''
'''RESIST [dose]'''
Line 397: Line 404:


It V1 mode it is customary to set M1 = (0,0) such that substrate height is detected at the center of the chip. In this way V1 mode can be used to exactly read out substrate height where the chip pattern will be written.
It V1 mode it is customary to set M1 = (0,0) such that substrate height is detected at the center of the chip. In this way V1 mode can be used to exactly read out substrate height where the chip pattern will be written.
=Beam current and condition files=
The beam current can in principle be changed in very fine steps, it however requires recalibration of the Dynamic Focus and Dynamic Stigmation table. Hence, only a limited number of beam currents are available. The available beam currents and condition file name are listed below.
{| class="wikitable"
|+  Condition files and beam current
|-
! Beam current [nA] !! Aperture !! Condition file
|-
| 0.12 || 4 || 0.12na_ap4
|-
| 0.16 || 4 || 0.16na_ap4
|-
| 0.22 || 4 || 0.22na_ap4
|-
| 0.4 || 4 || 0.4na_ap4
|-
| 0.5 || 4 || 0.5na_ap4
|-
| 0.8 || 4 || 0.8na_ap4
|-
| 1.4 || 4 || 1.4na_ap4
|-
| 1.6 || 4 || 1.6na_ap4
|-
| 2 || 4 || 2na_ap4
|-
| 2.7 || 4 || 2.7na_ap4
|-
| 3.8 || 5 || 3.8na_ap5
|-
| 4 || 4 || 4na_ap4
|-
| 5 || 5 || 5na_ap5
|-
| 6 || 5 || 6na_ap5
|-
| 10 || 6 || 10na_ap6
|-
| 12 || 5 || 12na_ap5
|-
| 14 || 8 || 14na_ap8
|-
| 19 || 7 || 19na_ap7
|-
| 21 || 7 || 21na_ap7
|-
| 22 || 7 || 22na_ap7
|-
| 25 || 7 || 25na_ap7
|-
| 27 || 7 || 27na_ap7
|-
| 29 || 7 || 29na_ap7
|-
| 30 || 8 || 30na_ap8
|-
| 36 || 8 || 36na_ap8
|-
| 41 || 8 || 41na_ap8
|-
| 44 || 8 || 44na_ap8
|-
| 54 || 7 || 54na_ap7
|-
| 60 || 8 || 60na_ap8
|}
Retrieved from "https://labadviser.nanolab.dtu.dk//index.php?title=Specific_Process_Knowledge/Lithography/EBeamLithography/JEOLJobPreparation"