Specific Process Knowledge/Lithography/UVExposure

The contents on this page, including all images and pictures, was created by DTU Nanolab staff unless otherwise stated.

Feedback to this page: click here

UV Exposure Comparison Table

Equipment		Aligner: MA6-1	Aligner: MA6-2	Aligner: Maskless 01	Aligner: Maskless 02	Aligner: Maskless 03	Aligner: Maskless 04
Purpose		Top Side Alignment Back Side Alignment UV exposure	Top Side Alignment Back Side Alignment UV exposure (DUV exposure) Bond alignment	Top Side Alignment Maskless UV exposure	Top Side Alignment Back Side Alignment Maskless UV exposure	Top Side Alignment Back Side Alignment Maskless UV exposure	Top Side Alignment Maskless UV exposure Direct laser writing
Performance	Minimum feature size	~1 µm	~1 µm	~1 µm	~1 µm	~1 µm	~1 µm
	Exposure light/filters/spectrum	350W Hg lamp i-line filter (365nm notch filter) Intensity in Constant Intensity mode: 8mW/cm2 @ 365nm 303nm filter optional	500W Hg-Xe lamp i-line filter (365nm notch filter) Intensity in Constant Intensity mode: 11mW/cm2 @ 365nm UV350 optics optional UV250 optics optional	365nm LED	375nm laserdiodes	405nm laserdiodes	365nm LED 405nm diode laser
	Exposure mode	Flood exposure Proximity Contact: Soft contact Hard contact Vacuum contact	Flood exposure Proximity Contact: Soft contact Hard contact Vacuum contact	Projection: Pneumatic auto-focus	Projection: Optical auto-focus Pneumatic auto-focus	Projection: Pneumatic auto-focus	Projection: Optical auto-focus Pneumatic auto-focus Direct laser writing: Optical auto-focus Pneumatic auto-focus
Substrates	Batch size	1 small sample, down to 10x10 mm2 1 50 mm wafer 1 100 mm wafer 1 150 mm wafer	1 small sample, down to 10x10 mm2 1 50 mm wafer 1 100 mm wafer 1 150 mm wafer	1 small sample, down to 5x5 mm2 1 50 mm wafer 1 100 mm wafer 1 150 mm wafer	1 small sample, down to 3x3 mm2 1 50 mm wafer 1 100 mm wafer 1 150 mm wafer 1 200 mm wafer	1 small sample, down to 5x5 mm2 1 50 mm wafer 1 100 mm wafer 1 150 mm wafer	1 small sample, down to 3x3 mm2 1 50 mm wafer 1 100 mm wafer 1 150 mm wafer
	Allowed materials	All cleanroom materials except copper and steel Dedicated 2inch chuck for III-V materials	All cleanroom materials except copper and steel Dedicated chuck for III-V materials	All cleanroom materials	All cleanroom materials	All cleanroom materials	All PolyFabLab materials

Aligner: MA6-1

The Aligner: MA6-1 is located in PolyFabLab

SUSS Mask Aligner MA6 is designed for high resolution photolithography. The 365nm exposure wavelength version is capable of 1.25 (1.0) um resolution in vacuum contact. All contact exposure programs (vacuum, hard, soft, proximity) are supplied. Two alignment options are available: top side alignment (TSA) with a split field or a video microscope and back side alignment (BSA) with BSA microscope. It is also possible to make IR- light alignment.

Training videos:

Operation

Alignment

The user manual(s), quality control procedure(s) and results and contact information can be found in LabManager - requires login

Exposure dose

Information on UV exposure dose

Process information

The Aligner: MA6-1 has an i-line notch filter installed. This results in an exposure light peak around 365nm with a FWHM of 7nm.

Link to information about alignment mark design and locations.

Quality Control (QC)

Quality Control (QC) for KS Aligner

The QC procedure for Aligner: MA6-1 - requires login The newest QC data for Aligner: MA6-1 - requires login QC Recipe: Manual intensity measurement Measurement area 100 mm Number of measurements 5 QC limits Aligner: MA6-1 Nominal intensity 8 mW/cm2 @ 365 nm Intensity deviation from nominal ≤5% Intensity non-uniformity ≤2% Power supply and/or lamp will be adjusted if intensity is outside the limit.

Equipment performance and process related parameters

Purpose		Alignment and UV exposure
Performance	Exposure mode	vacuum contact, hard contact, soft contact, proximity, flood exposure
	Exposure light/filters	broadband (i-, g-, h-line) 365 nm (i-line) 303 nm
	Minimum structure size	down to 1.25µm
	Mask size	5x5 inch 7x7 inch special holder for 4 x 2" designs on 5x5 inch
	Alignment modes	Top side (TSA) Backside (BSA)
Substrates	Substrate size	small pieces 1x1cm 50 mm wafers 100 mm wafers 150 mm wafers
	Allowed materials	All cleanroom materials Dedicated chuck for III-V materials
	Batch	1

Aligner: MA6-2

The Aligner: MA6-2 is placed in E-4

The Süss MicroTek Mask Aligner MA6 is designed for high resolution photolithography. The 365nm exposure wavelength version is capable of 1.25 (1.0) um resolution in vacuum contact. All contact exposure programs (vacuum, low vacuum, hard, soft, proximity) are supplied. Two alignment options are available: top side alignment (TSA) with a split field or a video microscope and back side alignment (BSA) with BSA (video) microscope.

The aligner can also be used for bond alignment (for Wafer Bonder 02). Special training is required.

Training videos:

Operation

Alignment

The user manual, quality control procedures and results, user APVs, and contact information can be found in LabManager - requires login

Exposure dose

Information on UV exposure dose

Process information

The Aligner: MA6-2 has an i-line notch filter installed. This results in an exposure light peak at 365nm. Compared to exposure on the KS Aligner, the optimal dose should be very similar. The 500W Hg-Xe lamp also enables exposure in the DUV range around 240nm. This functionality is not established yet, partly due to safety concerns.

Link to information about alignment mark design and locations.

Quality Control (QC)

Quality Control (QC) for Aligner: MA6-2

The QC procedure for Aligner: MA6-2 - requires login The newest QC data for Aligner: MA6-2 - requires login QC Recipe: Manual intensity measurement Measurement area 100 mm Number of measurements 5 QC limits Aligner: MA6-2 Nominal intensity 11 mW/cm2 @ 365 nm Intensity deviation from nominal ≤5% Intensity non-uniformity ≤2% Power supply and/or lamp will be adjusted if intensity is outside the limit.

Alignment

Top Side Alignment:

• TSA microscope standard objectives: 5X, and 10X (20X available)
• TSA microscope special objectives: 11.25X offset (for smaller separation)

• Minimum distance between TSA microscope objectives: 33 mm (8 mm for special objectives)
• Maximum distance between TSA microscope objectives: 160 mm
• TSA microscope travel range: X +/- 25mm; Y +20mm / -75mm (towards flat)

BackSide Alignment:

• Minimum distance between BSA microscope objectives: 15 mm
• Maximum distance between BSA microscope objectives: 100 mm
• BSA microscope travel range: X +50mm / -16mm; Y +50mm / -20mm (towards flat)
• BSA chuck view ranges:
  • 2": X +/- 8-22mm; Y +/- 0-6mm
  • 4": X +/- 14-46mm; Y +/- 0-10mm
  • 6": X +/- 14-69mm; Y +/- 0-10mm

Microscope field of view (W x H, splitfield):

• TSA 5X
  • Oculars: 1.3mm x 2.6mm (Ø2.6mm full field)
  • Camera: 350µm x 500µm (700µm x 500µm full field)
• TSA 10X
  • Oculars: 0.6mm x 1.3mm (Ø1.3mm full field)
  • Camera: 150µm x 250µm (350µm x 250µm full field)
• TSA special
  • Oculars: 0.55mm x 1.1mm (Ø1.1mm full field)
  • Camera: 150µm x 200µm (300µm x 200µm full field)
• BSA camera
  • Low: 1.5mm x 2mm (3mm x 2mm full field)
  • High: 450µm x 650µm (950µm x 650µm full field)

Equipment performance and process related parameters

Purpose		Mask alignment and UV exposure, potentially DUV exposure 1) Bond alignment
Performance	Exposure mode	vacuum contact, hard contact, soft contact, proximity, flood exposure
	Exposure light/filters	broadband (i-, g-, h-line) 365 nm (i-line) "UV300" (280-350 nm) DUV (240 nm) 1)
	Minimum structure size	Typically 1.25 µm, possibly down to 0.8 µm 1)
	Mask size	5x5 inch 7x7 inch special holder for 4 x 2" designs on 5x5 inch
	Alignment modes	Top side (TSA) Backside (BSA)
Substrates	Substrate size	small pieces 1x1cm 50 mm wafers 100 mm wafers 150 mm wafers
	Allowed materials	All cleanroom materials except copper and steel Dedicated chuck for III-V materials
	Batch	1

¹⁾ Not available yet. Requires tool change. Would require safety investigation (and a dedicated project) to become available.

Light intensity and uniformity after lamp ignition

Light intensity and uniformity after lamp ignition. CP is constant power mode, CI is constant intensity mode. The accept limits for the CI mode is ±5%, the accept limit for the non-uniformity is 2%. CP mode has no accept limit.

The lamp requires about 15 minutes of on-time after lamp ignition, before the light output has stabilized, and users using the constant power mode should always wait for 15 minutes after ignition, before starting processing.

If users use the constant intensity mode, this waiting time is not necessary, since the internal light sensor automatically adjusts the output to match the setpoint value.

The non-uniformity of the light, in CI mode, is unaffected by the stabilization time.

Aligner: Maskless 01

Aligner: Maskless 01 positioned in E-5 (2017)

The logon password for the PC is "mla" (without quotation marks).

The MLA 100 Maskless Aligner located in the E-4 cleanroom is a direct exposure lithography tool installed in 2017. It is a UV LED exposure system, that exposes the patterns directly on photosensitive resists on chips, 2, 4, and 6 inch substrates, without prior fabrication of the mask. The system offers top side alignment with high accuracy.

Link to information about alignment mark design.

The user manual and contact information can be found in LabManager:

Equipment info in LabManager - requires login

Exposure dose and defocus

Information on UV exposure dose

Process information

• Exposure technology
• Process parameters
• Substrate positioning
• Alignment
• Optimal use of the maskless aligner

Equipment performance and process related parameters

Purpose		Alignment and UV exposure
Performance	Exposure mode	Projection
	Exposure light	365nm (LED), FWHM=8nm
	Focusing method	Pneumatic
	Minimum structure size	down to 1µm
	Design formats	GDS-II CIF DXF Gerber HIMT format
	Alignment modes	Top side only
Substrates	Substrate size	maximum writing area: 125x125 mm2 150 mm wafer 100 mm wafer 50 mm wafer pieces down to 5x5 mm2
	Allowed materials	All cleanroom materials
	Batch	1

Aligner: Maskless 02

MLA150 WMII maskless aligner from Heidelberg Instruments GmbH (installed 2019 as WMI (0.6µm resolution), rebuilt to WMII 2023).

Special features

• Optical Autofocus
• Backside Alignment
• Basic Gray Scale Exposure
• Advanced Field Alignment Mode for alignment to individual chips/devices on the substrate
• High Aspect Ratio Mode for exposure of thick resists
• 200 x 200 mm exposure field
• Separate conversion PC

Link to information about alignment mark design.

Training videos

Equipment info in LabManager - requires login

Exposure dose and defocus

Information on UV exposure dose

Process information

• Exposure technology
• Process Parameters
• Features
• Alignment

Equipment performance and process related parameters

Purpose		Alignment and UV exposure
Performance	Exposure mode	Projection
	Exposure light	375 nm (laser diode arrays)
	Focusing method	Optical Pneumatic
	Minimum structure size	down to 1 µm
	Design formats	GDS-II CIF DXF Gerber HIMT format
	Alignment modes	Top side alignment Backside alignment Field alignment (chip-by-chip TSA)
Substrates	Substrate size	maximum writing area: 200x200 mm2 200 mm wafer 150 mm wafer 100 mm wafer 50 mm wafer pieces down to 3x3 mm2 1)
	Allowed materials	All cleanroom materials
	Batch	1

¹⁾ with optical autofocus

Aligner: Maskless 03

MLA150 WMII maskless aligner from Heidelberg Instruments GmbH, installed 2020.

Special features:

• Backside Alignment
• Advanced Field Alignment Mode for alignment to individual chips/devices on the substrate
• Separate conversion PC (Power PC)

Link to information about alignment mark design.

Training videos

Equipment info in LabManager - requires login

Exposure dose and defocus

Information on UV exposure dose

Process information

• Exposure technology
• Process Parameters
• Features
• Alignment

Equipment performance and process related parameters

Purpose		Alignment and UV exposure
Performance	Exposure mode	Projection
	Exposure light	405nm (laser diode array)
	Focusing method	Pneumatic
	Minimum structure size	down to 1 µm
	Design formats	GDS-II CIF DXF Gerber HIMT format
	Alignment modes	Top side alignment Backside alignment Field alignment (chip-by-chip TSA)
Substrates	Substrate size	maximum writing area: 150x150 mm2 150 mm wafer 100 mm wafer 50 mm wafer pieces down to 5x5 mm2
	Allowed materials	All cleanroom materials
	Batch	1

Aligner: Maskless 04

Aligner: Maskless 04 is installed in PolyFabLab in building 347.

The logon password for the PC is "mla" (without quotation marks).

The µMLA Tabletop Maskless Aligner from Heidelberg, located in PolyFabLab in building 347, is a direct exposure lithography tool installed in 2024. It is a UV exposure system, that exposes the patterns directly on photosensitive resists on chips, 2, 4, and 6 inch substrates, without prior fabrication of a mask. The system offers top side alignment with good accuracy.

Link to information about alignment mark design.

The user manual and contact information can be found in LabManager:

Equipment info in LabManager - requires login

Process information

• Exposure technology
• Process parameters
• Substrate positioning
• Alignment

Equipment performance and process related parameters

Purpose		Alignment and UV exposure
Performance	Exposure mode	Projection (Raster mode) Direct laser writing (Vector mode)
	Exposure light	365nm (LED) for projection 405nm (diode laser) for direct laser writing
	Focusing method	Pneumatic or Optical
	Minimum structure size	Down to 1µm
	Design formats	GDS-II CIF DXF Gerber HIMT format
	Alignment modes	Top side only
Substrates	Substrate size	maximum writing area: 150x150 mm2 150 mm wafer 100 mm wafer 50 mm wafer pieces down to 3x3 mm2 with optical autofocus
	Allowed materials	All PolyFabLab materials with sufficient stiffness and flatness.
	Batch	1