Specific Process Knowledge/Etch/ICP Metal Etcher/Chromium/End point: Difference between revisions
| (9 intermediate revisions by 2 users not shown) | |||
| Line 3: | Line 3: | ||
Made by Berit bghe @ DTU Nanolab | Made by Berit bghe @ DTU Nanolab | ||
| Line 12: | Line 11: | ||
==Etch close to optimal== | ==Etch close to optimal== | ||
The etch rate is faster near the edge. Therefor the trenches are in general wider at the edges. Here all structures has been etched down to the SiO2 layer and the dimensions are close to being unaffected, especially in the middel. The sidewalls are close to 90 degrees; Sometimes a little positive and sometimes a little negative. | The etch rate is faster near the edge. Therefor the trenches are in general wider at the edges. Here all structures has been etched down to the SiO2 layer and the dimensions are close to being unaffected, especially in the middel. The sidewalls are close to 90 degrees; Sometimes a little positive and sometimes a little negative. To improve more the etch rate should be more uniform over the wafer and the Cr should be with small grain sizes. I stopped '''41 s after the end point curve 'SUM_C2' top point on the barc etch''' and '''170 s after the end point curve 'CR_Avg_5208' started to drop on the Cr etch'''. | ||
{| class="wikitable" | {| class="wikitable" | ||
| Line 28: | Line 27: | ||
File:S047676midt_cr_02.jpg | File:S047676midt_cr_02.jpg | ||
File:S047676midt_cr_04.jpg | File:S047676midt_cr_04.jpg | ||
</gallery> | </gallery> | ||
| | | | ||
<gallery caption="S047676 X min, Feb-2025, wafer edge, 100 nm Cr mask, with 500 nm resist" widths="600px" heights="550px" perrow="1"> | <gallery caption="S047676 X min, Feb-2025, wafer edge, 100 nm Cr mask, with 500 nm resist" widths="600px" heights="550px" perrow="1"> | ||
File:S047676edge_cr_01.jpg | File:S047676edge_cr_01.jpg | ||
File:S047676edge_cr_04.jpg | File:S047676edge_cr_04.jpg | ||
| Line 39: | Line 36: | ||
File:S047676edge_cr_11.jpg | File:S047676edge_cr_11.jpg | ||
File:S047676edge_cr_12.jpg | File:S047676edge_cr_12.jpg | ||
File:Emptyimage.jpg | |||
</gallery> | </gallery> | ||
| Line 62: | Line 59: | ||
==Etched too long== | ==Etched too long== | ||
The etch rate is faster near the edge. Therefor the trenches are in general wider at the edges. Here all structures has been etched down to the SiO2 layer but the dimensions | The etch rate is faster near the edge. Therefor the trenches are in general wider at the edges. Here all structures has been etched down to the SiO2 layer but the dimensions are affected, especially at the edge the trenches have become wider. The sidewalls are close to 90 degrees; Sometimes a little positive and sometimes a little negative. The improve more the etch time should be decreased. | ||
{| class="wikitable" | {| class="wikitable" | ||
| Line 89: | Line 86: | ||
File:S047670edge_cr_04.jpg | File:S047670edge_cr_04.jpg | ||
File:S047670edge_cr_06.jpg | File:S047670edge_cr_06.jpg | ||
File:Emptyimage.jpg | |||
File:S047670edge_cr_08.jpg | File:S047670edge_cr_08.jpg | ||
File:S047670edge_cr_09.jpg | File:S047670edge_cr_09.jpg | ||
| Line 100: | Line 97: | ||
=== End point signal=== | === End point signal=== | ||
====Barc etch==== | ====Barc etch==== | ||
The End point signal shows a top point after 5. | The End point signal shows a top point after 5.0 s and I stopped the etch after 60 s. | ||
<gallery caption="S047670 60s barc etch, Feb-2025, wafer center, 100 nm Cr mask, with 500 nm resist" widths="600px" heights="550px" perrow="2"> | |||
File:20250213_02_endpoint.jpg | |||
File:20250213_02_toppoint.jpg | |||
</gallery> | </gallery> | ||
====Cr etch==== | ====Cr etch==== | ||
The End point signal shows a drop after | The End point signal shows a drop after 264 s and I stopped the etch after 7:45 min | ||
<gallery caption="S047670 7:45 min Cr etch, Feb-2025, wafer center, 100 nm Cr mask, with 500 nm resist" widths="600px" heights="550px" perrow="2"> | |||
File:20250213_04_droppoint.jpg | |||
File:20250213_04_endpoint.jpg | |||
</gallery> | </gallery> | ||
| Line 156: | Line 157: | ||
=== End point signal=== | === End point signal=== | ||
====Barc etch==== | ====Barc etch==== | ||
The End point signal shows a top point after | The End point signal shows a top point after 6.5 s and I stopped the etch after 30 s. Too short | ||
<gallery caption=" | <gallery caption="S047671 30s barc etch, Feb-2025, wafer center, 100 nm Cr mask, with 500 nm resist" widths="600px" heights="550px" perrow="2"> | ||
File:20250213_06_endpoint.jpg | File:20250213_06_endpoint.jpg | ||
| Line 166: | Line 167: | ||
====Cr etch==== | ====Cr etch==== | ||
The End point signal shows a drop after 295 s and I stopped the etch after | The End point signal shows a drop after 295 s and I stopped the etch after 7:00 min. Too short | ||
<gallery caption=" | <gallery caption="S047671 7:00 min Cr etch, Feb-2025, wafer center, 100 nm Cr mask, with 500 nm resist" widths="600px" heights="550px" perrow="2"> | ||
File:20250213_08_droppoint.jpg | File:20250213_08_droppoint.jpg | ||