Feedback to this page: click here

Descum results

Plasma asher 1

The user manual(s), quality control procedure(s) and results and contact information can be found in LabManager.

Descum of AZ5214E resist on 50mm silicon wafer. Wafer was placed horisontally in chamber on a 100 mm carier wafer.

Recipe 1:
Note: Plasma asher was cold before use

O2 flow: 70 ml/min
N2 flow: 70 ml/min
Power: 150 W

Ashing time (min)	1	2	5	7	10	10
Etched Thickness (nm)	14.2	16.3	47.6	123.2	854.3	862.1

Recipe 2:
Note: Plasma asher was cold before use

O2 flow: 500 ml/min
N2 flow: 0 ml/min
Power: 500 W

Ashing time (min)	1	2	5	7	10	10
Etched Thickness (nm)		8.1	32.9	271.1	495.6	446.2

Descum tests on various resists

Conny Hjort & Jesper Hanberg, September 2019

Descum of different resists, AZ5214E, AZ701 MiR and AZ2020 nLOF, on a single 100mm wafer was tested. Wafer was placed vertically in the middle of glass carrier. Recipe setting was the same as in previous test in September 2019: 70ml/min O2, 70 ml/min N2, power 150W, different ashing time 1, 2, 3, 5 and 7 min run. Plasma Asher was cold before use, we observed minor temperature rise during processing, but not more than 5 degrees. Starting chambers pressure was around 0, 5 mbar.

1,5 um AZ5214E resist

Ashing time (min)	1	2	3	5	7
Etched Thickness (nm)	6,28	102,99	76,92	N/A	N/A

1,5 um AZ5214E resist placed horizontally in the carrier

Ashing time (min)	1	2	3	5	7
Etched Thickness (nm)	63,03	143,32	304,29	372,59	N/A

1,5 um AZ701MiR resist

Ashing time (min)	1	2	3	5	7
Etched Thickness (nm)	268,88	199,54	219,03	200,86	292,15

1,5 um AZ 2020nLOF resist

Ashing time (min)	1	2	3	5	7
Etched Thickness (nm)	1,68	76,51	169,72	481,96	272,59

Plasma asher 2

Descum of AZ Mir 701 resist on 100mm silicon wafer. Five wafers were placed vertically in chamber.

Experiment parameters:

	O2 flow	N2 flow	Power
recipe 1	100	100	150
recipe 2	500	0	200

recipe 1

Ashing time (min)	1	2	3	4	6	7	8	9	10	12	14	15	20
Etched Thickness (nm)	8,7	5,1	12,5	6,2	31,8	86,0	25,7	46,8	38,3	49,7	59,4	140,1	360,7
Initial temperature (°C)	28	21	31	21	22	28	25	24	21	24	24	22	22

recipe 2

Ashing time (min)	1	2	3	4	5	6	7	8	10	12	15	20
Etched Thickness (nm)	8,1	9,4	16,8	55,2	44,0	47,5	42,5	55,1	85,3	122,4	184,8	305,9
Initial temperature (°C)	22	21	21	22	22	22	21	21	20	21	21	22

We can observe linear dependance of etched material on time after etching 7 minutes and more (recipe 2).

Jitka Urbánková & Jesper Hanberg December 2019

Plasma asher 3

Plasma Asher 3 is specially used for control descum process after lithography. Please notice that you only can process one 4 inch wafer or one small sampel at a time. Machine is equipped with 2 gaslines: oxygen and nitrogen, but all tests run with oxygen as recommended by Diener.

Ashing of AZ MiR701 resist

You can use different strategy planing your descum: you can change power settings or you can vary chamber pressure during descum.

Testing different power settings

Descum results for different power settings

Recipe settings: Kept oxygen and pressure settings constant at Oxygen: 5 sccm under process; Pressure: 0,2mbar and vary power.

Experiment parameters:

	FW/REV	C2/C1	Power
recipe 1	50/0	52/31	50%
recipe 2	100/0	53/31	100%
recipe 3	20/0	51/34	20%

Testing different pressure settings

Recipe settings: Kept power setting constant at Power: 100% and vary oxygen flow during process.

Descum results for different pressure settings

Experiment parameters:

	FW/REV	C2/C1	Oxygen	Pressure
recipe 1	100/0	53/31	5	0,2
recipe 2	100/0	37/38	45	0,8

Ashing of AZ5214E resist

Recipe settings: Kept power setting constant at Power: 100% and vary oxygen flow during process.

Experiment parameters:

	FW/REV	C2/C1	Oxygen	Pressure
recipe 1	100/0	53/31	17	0,4
recipe 2	100/0	37/39	45	0,8