Specific Process Knowledge/Thin film deposition/Deposition of Silicon Nitride: Difference between revisions

Revision as of 15:02, 25 November 2019

Feedback to this page: click here

Deposition of silicon nitride

Deposition of silicon nitride can be done with either LPCVD (Low Pressure Chemical Vapor Deposition) or PECVD (Plasma Enhanced Chemical Vapor Deposition). Stoichiometric nitride or silicon rich (low stress) LPCVD nitride is deposited on a batch of wafers in a LPCVD nitride furnace, and PECVD nitride (or oxynitride) is deposited on a few samples at a time in a PECVD system. LPCVD nitride has a good step coverage and a very good uniformity. Using PECVD it is possible to deposit a much lower temperature and a thicker layer of nitride on different types of samples, but the nitride does not cover sidewalls very well.

It is also possible to deposit silicon nitride using the Lesker sputter system.

Nitride deposition using PECVD (or oxynitride)

Nitride deposition using Lesker sputter system

Comparison of LPCVD, PECVD and Lesker sputter system for silicon nitride deposition

	LPCVD	PECVD	Lesker sputter system
Generel description	Low Pressure Chemical Vapour Deposition (LPCVD furnace process)	Plasma Enhanced Chemical Vapour Deposition (PECVD process)	Reactive sputtering
Stoichiometry	Stoichiometric nitride, Si₃N₄ Silicon rich (low stress) nitride, SRN	Si_xN_yH_z Si_xO_yN_zH_v Silicon nitride can be doped with boron or phosphorus	Unknown
Film thickness	Stoichiometric nitride: ~5 nm - ~230 nm Silicon rich (low stress) nitride: ~5 nm - ~335 nm Thicker nitride layers can be deposited over more runs (maximum two)	~40 nm - 10 µm	limited by process time. Deposition rate is ~1.7nm/min
Process temperature	Stoichiometric nitride: 780 ^oC - 800 ^oC Silicon rich (low stress) nitride: 810 ^oC - 845 ^oC	300 ^oC	Room temperature (higher temperature possible)
Step coverage	Good	Less good	yes, but amount unknown
Film quality	Deposition on both sides og the substrate Dense film Few defects	Deposition on one side of the substrate Less dense film Incorporation of hydrogen in the film	Deposition on one side of the substrate unknown quality
KOH etch rate (80 ^oC)	Expected <1 Å/min	Dependent on recipe: ~1-10 Å/min	Unknown
BHF etch rate	Very low	Very high compared the LPCVD nitride	Unknown
Batch size	1-15 100 mm wafers (4" furnace), 1-25 100 mm wafers (6" furnace) 1-25 150 mm wafers (only 6" furnace)	Several smaller samples 1-7 50 mm wafers 1 100 mm wafers 1 150 mm wafer Depending on what PECVD you use	Several smaller samples 1-several 50 mm wafers 1100 mm wafers 1150 mm wafer
Allowed materials	Silicon Silicon oxide Silicon nitride Pure quartz (fused silica) Processed wafers have to be RCA cleaned	Silicon Silicon oxide (with boron, phosphorous) Silicon nitrides (with boron, phosphorous) Pure quartz (fused silica) III-V materials (in PECVD4) Small amount of metals (in PECVD3)	Any

@@ Line 168: / Line 168: @@
 ==Deposition of Silicon Nitride using LPCVD==
-LPCVD silicon nitride can be deposited in a [[Specific Process Knowledge/Thin film deposition/B2 Furnace LPCVD Nitride|LPCVD nitride furnace]]. Danchip has two LPCVD nitride furnaces: A new furnace (installed in 2008) for deposition of stoichiometric nitride on 4" or on 6" wafers and an older furnace (installed in 1995) for deposition of stoichiometric nitride and low stress nitride on 4" wafers.
+LPCVD silicon nitride can be deposited in a [[Specific Process Knowledge/Thin film deposition/B2 Furnace LPCVD Nitride|LPCVD nitride furnace]]. DTU Nanolab has two LPCVD nitride furnaces: A new furnace (installed in 2008) for deposition of stoichiometric nitride on 4" or on 6" wafers and an older furnace (installed in 1995) for deposition of stoichiometric nitride and low stress nitride on 4" wafers.
 The LPCVD nitride deposition is a batch process, meaning that nitride can be deposited on a batch of up to 15 wafers (in the old nitride furnace) or 25 wafers (in the new nitride furnace) at a time. The deposition takes place at temperatures of 780-845 degrees Celsius and at a pressure of 120-200 mTorr. The LPCVD silicon nitride has a good step coverage, and the film thickness is very uniform over the wafers. On the furnaces there are standard processes for deposition of stoichiometric nitride (Si<sub>3</sub>N<sub>4</sub>) and for deposition of low stress nitride (SRN) (only on the old nitride furnace).