Specific Process Knowledge/Lithography/Descum

Feedback to this page: click here

Plasma asher 1

Descum results plasma asher 1. September 2019

The user manual(s), quality control procedure(s) and results and contact information can be found in LabManager.

Descum of AZ5214E resist on 50mm silicon wafer. Wafer was placed horisontally in chamber on a 100 mm carier wafer.

Recipe 1:
Note: Plasma asher was cold before use

• O2 flow: 70 ml/min
• N2 flow: 70 ml/min
• Power: 150 W

Ashing time (min) 1 2 5 7 10 10 Etched Thickness (nm) 14.2 16.3 47.6 123.2 854.3 862.1

Recipe 2:
Note: Plasma asher was cold before use

• O2 flow: 500 ml/min
• N2 flow: 0 ml/min
• Power: 500 W

Ashing time (min) 1 2 5 7 10 10 Etched Thickness (nm) - 8.1 32.9 271.1 495.6 446.2

Descum tests on UV resists

Conny Hjort & Jesper Hanberg, September 2021

Descum results plasma asher 1. August 2021

Descum of different resists, AZ5214E, AZ701 MiR and AZ2020 nLOF, on a single 100mm wafer was tested. Wafer was placed vertically in the middle of glass carrier.

Recipe settings:
Note: plasma Asher was cold before use.

• O2 flow: 70 ml/min
• N2 flow: 70 ml/min

Power: 150 W

Minor temperature rise during processing was observed, but not more than 5 degrees. Starting chamber pressure was around 0.5 mbar.

1,5 um AZ5214E resist

Ashing time (min) 1 2 3 5 7 Etched Thickness (nm) 6,28 102,99 76,92 N/A N/A

1,5 um AZ5214E resist placed horizontally in the carrier

Ashing time (min) 1 2 3 5 7 Etched Thickness (nm) 63,03 143,32 304,29 372,59 N/A

1,5 um AZ701MiR resist

Ashing time (min) 1 2 3 5 7 Etched Thickness (nm) 268,88 199,54 219,03 200,86 292,15

1,5 um AZ 2020nLOF resist

Ashing time (min) 1 2 3 5 7 Etched Thickness (nm) 1,68 76,51 169,72 481,96 272,59

Plasma asher 2

Descum results plasma asher 2 - recipe 1

Descum of AZ Mir 701 resist on 100mm silicon wafer. Five wafers were placed vertically in chamber.

Experiment parameters:

O2 flow N2 flow Power recipe 1 100 100 150 recipe 2 500 0 200

recipe 1

Ashing time (min) 1 2 3 4 6 7 8 9 10 12 14 15 20 Etched Thickness (nm) 8,7 5,1 12,5 6,2 31,8 86,0 25,7 46,8 38,3 49,7 59,4 140,1 360,7 Initial temperature (°C) 28 21 31 21 22 28 25 24 21 24 24 22 22

Descum results plasma asher 2 - recipe 2

recipe 2

Ashing time (min) 1 2 3 4 5 6 7 8 10 12 15 20 Etched Thickness (nm) 8,1 9,4 16,8 55,2 44,0 47,5 42,5 55,1 85,3 122,4 184,8 305,9 Initial temperature (°C) 22 21 21 22 22 22 21 21 20 21 21 22

We can observe linear dependance of etched material on time after etching 7 minutes and more (recipe 2).

Jitka Urbánková & Jesper Hanberg December 2019

Plasma asher 3

Plasma Asher 3 is specially used for control descum process after lithography. Please notice that you only can process one 4 inch wafer or one small sampel at a time. Machine is equipped with 2 gaslines: oxygen and nitrogen, but all tests run with oxygen as recommended by Diener.

Ashing of AZ MiR701 resist

You can use different strategy planing your descum: you can change power settings or you can vary chamber pressure during descum.

Testing different power settings

Descum results for different power settings

Recipe settings: Kept oxygen and pressure settings constant at Oxygen: 5 sccm under process; Pressure: 0,2mbar and vary power.

Experiment parameters:

FW/REV C2/C1 Power recipe 1 50/0 52/31 50% recipe 2 100/0 53/31 100% recipe 3 20/0 51/34 20%

Testing different pressure settings

Recipe settings: Kept power setting constant at Power: 100% and vary oxygen flow during process.

Descum results for different pressure settings

Experiment parameters:

FW/REV C2/C1 Oxygen Pressure recipe 1 100/0 53/31 5 0,2 recipe 2 100/0 37/38 45 0,8

Ashing of AZ5214E resist

Descum results for different pressure settings

Recipe settings: Kept power setting constant at Power: 100% and vary oxygen flow during process.

Experiment parameters:

FW/REV C2/C1 Oxygen Pressure recipe 1 100/0 53/31 17 0,4 recipe 2 100/0 37/39 45 0,8